AltIMU-10 v3 Gyro, Accelerometer, Compass, and Altimeter (L3GD20H, LSM303D, and LPS331AP Carrier)

Pololu item #: 2469
Brand: Pololu
Status: Discontinued 
RoHS 3 compliant

This product has been discontinued.

This product has been replaced by the AltIMU-10 v5.

The Pololu AltIMU-10 v3 is an inertial measurement unit (IMU) and altimeter that features the same L3GD20H gyro and LSM303D accelerometer and magnetometer as the MinIMU-9 v3, and adds an LPS331AP digital barometer. An I²C interface accesses ten independent pressure, rotation, acceleration, and magnetic measurements that can be used to calculate the sensor’s altitude and absolute orientation. The board operates from 2.5 to 5.5 V and has a 0.1″ pin spacing.

Clearance: This board is being replaced by the newer AltIMU-10 v5.

 Description Specs (8) Pictures (7) Resources (20) FAQs (1) On the blog (5) 
Why are the accelerometer readings from my LSM303D stuck at an incorrect value?

We have noticed that the accelerometer in the LSM303D is particularly sensitive to brown-out conditions. If power is removed and the voltage on the 3.3 V power supply line falls significantly, but is not allowed to drop completely to 0 V, the accelerometer can be put into a bad state. When power is reapplied to the LSM303D, the accelerometer then returns readings on some or all axes that are large values and do not change much or at all. (We have often seen readings like -32760 and 24539.)

To prevent this problem from occurring, the voltage on the 3.3 V line must be allowed to fall to about 0 V when power is removed from the LSM303D. Depending on other loads and the amount of capacitance on the 3.3 V line, it can take up to several seconds for this to happen, meaning that you should avoid interrupting power to the LSM303D for any shorter period, and if such a short interruption does occur, you should remove power again for a longer period to allow the accelerometer to reset properly.

If the voltage takes too long to fall, you can add a resistor between 3.3 V and ground (a “bleeder resistor”) to discharge the 3.3 V line more quickly when power is removed. We suggest trying a resistor in the 1 kΩ to 10 kΩ range. (Note that a stronger bleeder resistor will cause the voltage to fall more quickly when power is removed, but it will also waste more power when the supply is present.)

The Zumo 32U4 includes a bleeder resistor on the 3.3 V line.

Related Products

AltIMU-10 v6 Gyro, Accelerometer, Compass, and Altimeter (LSM6DSO, LIS3MDL, and LPS22DF Carrier)
MinIMU-9 v6 Gyro, Accelerometer, and Compass (LSM6DSO and LIS3MDL Carrier)
LPS331AP Pressure/Altitude Sensor Carrier with Voltage Regulator
L3GD20H 3-Axis Gyro Carrier with Voltage Regulator
LSM303D 3D Compass and Accelerometer Carrier with Voltage Regulator
UM7 Orientation Sensor
UM7-LT Orientation Sensor
LOCOSYS LS20031 66-Channel GPS Receiver Module (MT3339 Chipset)
Logic Level Shifter, 4-Channel, Bidirectional

Related Categories

Accelerometers, Gyros, & Compasses
MEMS Sensors
Sensors
Development Boards (Programmable Controllers)
Premium Jumper Wires
Wires with Pre-Crimped Terminals
Crimp Connector Housings
Solderless Breadboards
Log In
Pololu Robotics & Electronics
Shopping cart
(702) 262-6648
Same-day shipping, worldwide
Menu
Shop Blog Forum Support
My account Comments or questions? About Pololu Contact Ordering information Distributors