7.5V, 3A Step-Down Voltage Regulator D30V30F7

This is a merged information page for Item #4894.
View normal product page.

Pololu item #: 4894
Brand: Pololu
Status: Active and Preferred 
RoHS 3 compliant


Output voltage Typical max current output1 Input voltage range2
7.5 V 3 A 7.5 V – 45 V

1 Typical continuous output current at 30 V in. Actual achievable continuous output current is a function of input voltage and is limited by thermal dissipation. See the output current graphs on the product pages for more information.
2 Minimum input voltage is subject to dropout voltage considerations; see the dropout voltage section of product pages for more information.


Alternatives available with variations in these parameter(s): output type Select variant…

Pictures

7.5V, 3A Step-Down Voltage Regulator D30V30F7.

Step-Down Voltage Regulator D30V30Fx pinout.

Step-Down Voltage Regulator D30V30Fx, bottom view with dimensions.

7.5V, 3A Step-Down Voltage Regulator D30V30F7, with included hardware.

7.5V, 3A Step-Down Voltage Regulator D30V30F7, top view.

Step-Down Voltage Regulator D30V30Fx, bottom view.

Step-Down Voltage Regulator D30V30Fx, side view.

Step-Down Voltage Regulator D30V30Fx, assembled on breadboard.

Typical efficiency of Step-Down Voltage Regulator D30V30F7.

Typical maximum continuous output current of Step-Down Voltage Regulator D30V30Fx.

Typical quiescent current of Step-Down Voltage Regulator D30V30Fx.

Typical dropout voltage of Step-Down Voltage Regulator D30V30Fx.




Overview

The D30V3x line of synchronous buck (step-down) voltage regulators generates lower output voltages from input voltages as high as 45 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters), which makes them much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. These regulators can typically support continuous output currents between 1 A and 4.5 A, depending on the input voltage and output voltage. In general, the available output current decreases as the input and output voltages increase.

D30V3x line of step-down voltage regulators. From left to right: D30V30Fx, D30V30MASx, D30V33MASx.

This line consists of the D30V30Fx family of fixed output voltages ranging from 3.3 V to 15 V and two families of adjustable versions that allow the output voltage to be set with a precision 11-turn potentiometer. Each adjustable option is available with or without an adjustable low-voltage cutoff (also set through a precision 11-turn potentiometer on the versions that have it). The adjustable families are the D30V30MAx, which is the more compact of the two thanks to its double-sided assembly, and the D30V33MAx, which includes larger through-holes for terminal blocks and can do slightly more current thanks to its larger surface area. The following table shows all of the members of the D30V3x line:

Regulator Output voltage Typical max
output current1
Input voltage2 Adjustable
low-voltage
cutoff
Size Price
#4891: D30V30F3 3.3 V 3.7 A 3.3 V – 45 V 0.7″ × 0.8″ $12.95
#4892: D30V30F5 5 V 3.4 A 5 V – 45 V $12.95
#4893: D30V30F6 6 V 3.3 A 6 V – 45 V $13.95
#4894: D30V30F7 7.5 V 3 A 7.5 V – 45 V $13.95
#4895: D30V30F9 9 V 2.9 A 9 V – 45 V $13.95
#4896: D30V30F12 12 V 2.8 A 12 V – 45 V $13.95
#4897: D30V30F15 15 V 2.7 A 15 V – 45 V $13.95
#4873: D30V30MAL 1.4 V – 7 V 3.4 A 3.3 V – 45 V 0.6″ × 1.0″ $16.95
#4872: D30V30MALCMA $19.95
#4875: D30V30MAS 4.2 V – 15 V 3 A 4.2 V – 45 V $16.95
#4874: D30V30MASCMA $19.95
#4853: D30V33MAL 1.4 V – 7 V 3.8 A 3.3 V – 45 V 0.9″ × 1.2″ $17.95
#4852: D30V33MALCMA $20.95
#4855: D30V33MAS 4.2 V – 15 V 3.3 A 4.2 V – 45 V $17.95
#4854: D30V33MASCMA $20.95
1At 30 V in. Actual achievable continuous output current is a function of input and output voltages and is limited by thermal dissipation.
2Operating voltage must be higher than the set output voltage and is subject to dropout voltage considerations.

The regulators have reverse voltage protection up to 40 V, input under-voltage lockout, over-current protection, and short-circuit protection. A thermal shutdown feature also helps prevent damage from overheating and a soft-start feature limits the inrush current and gradually ramps the output voltage on startup.

If you need higher input voltages, consider the similar D36V28Fx family, which works up to 50 V in, and if you need more output current, consider the similar D36V50Fx family of step-down voltage regulators.

We manufacture these boards in-house at our Las Vegas facility, which gives us the flexibility to make these regulators with customized components to better meet the needs of your project. For example, if you have an application where the input voltage will always be below 20 V and efficiency is very important, we can make these regulators a bit more efficient at high loads by replacing the 40V reverse voltage protection MOSFET with a 20V one. We can also customize the output voltage. If you are interested in customization, please contact us for a quote.

Details for item #4894

This item is the D30V30F7.5, which outputs a fixed 7.5 V.

7.5V, 3A Step-Down Voltage Regulator D30V30F7, top view.

Step-Down Voltage Regulator D30V30Fx, bottom view.

Features

Using the Regulator

Connections

This regulator has six connections: power good (PG), enable (EN), input voltage (VIN), output voltage (VOUT), and two ground (GND) connections.

The “power good” indicator, PG, is an open-drain output that goes low when the regulator’s output voltage either rises more than 7.5% (typical) above or falls more than 9% (typical) below the nominal voltage (with hysteresis). An external pull-up resistor is required to use this pin.

The regulator, which is enabled by default, can be put into a low-power sleep state by reducing the voltage on the EN pin below 0.85 V (typical; the actual threshold can vary between 0.65 V and 1.05 V from unit to unit), and it can be brought out of this state again by increasing the voltage on EN past 1 V (typical). The shutdown current draw in this sleep mode is dominated by the current in the 100 kΩ pull-up resistor from EN to VIN and in the reverse-voltage protection circuit, which altogether will be between 10 µA and 20 µA per volt on VIN. (Note that for high input voltages, the shutdown current draw when it is disabled can be greater than the quiescent draw while enabled; see the quiescent current graph below for more details.)

A low-voltage cutoff can be set by adding an appropriately sized external pull-down resistor between EN and GND. This resistor and the on-board 100 kΩ pull-up would together form a VIN voltage divider with the output connected to EN.

The input voltage, VIN, powers the regulator. Voltages between 3.3 V and 45 V can be applied to VIN, but generally the effective lower limit of VIN is VOUT plus the regulator’s dropout voltage, which varies approximately linearly with the load (see below for graphs of the dropout voltage as a function of the load).

VOUT is the regulated output voltage.

Included hardware

Step-Down Voltage Regulator D30V30Fx, with included hardware.

The six connection through-holes are arranged on a 0.1″ grid for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. The PG connection is the only one not located along the edge of the board. A 6×1 straight male header strip and a 5×1 right-angle male header strip are included with the regulator; one pin of the straight header can optionally be separated with a pair of flush cutters and soldered into PG.

Typical efficiency

The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns.

Maximum continuous output current

The maximum achievable output current of these regulators varies with the input voltage but also depends on other factors, including the ambient temperature, air flow, and heat sinking. The graph below shows maximum output currents that these regulators can deliver continuously at room temperature in still air and without additional heat sinking.

During normal operation, this product can get hot enough to burn you. Take care when handling this product or other components connected to it.

Quiescent current

The quiescent current is the current the regulator uses just to power itself, and the graph below shows this for the different regulator versions as a function of the input voltage. The module’s EN input can be driven low to put the board into a low-power state where it typically draws between 10 µA and 20 µA per volt on VIN.

Typical dropout voltage

The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V. Generally speaking, the dropout voltage increases as the output current increases. The graph below shows the dropout voltages for the different members of this regulator family:

Dimensions

Size: 0.7″ × 0.8″ × 0.35″1
Weight: 3.3 g1

General specifications

Minimum operating voltage: 7.5 V2
Maximum operating voltage: 45 V
Continuous output current: 3 A3
Output voltage: 7.5 V
Reverse voltage protection?: Y4
Maximum quiescent current: 13 mA5
Output type: fixed 7.5V

Identifying markings

PCB dev codes: reg32a
Other PCB markings: 0J14242

Notes:

1
Without included optional headers.
2
Subject to dropout voltage considerations. See the dropout voltage graph under the description tab for more information.
3
Typical maximum continuous output current at 30 V in. Actual achievable continuous output current is a function of input voltage and is limited by thermal dissipation. See the output current graph under the description tab for more information.
4
To -40 V. Connecting supplies over 40 V in reverse can damage the device.
5
While enabled with no load. The maximum quiescent current occurs at lower input voltages. It is reduced to under 1 mA with higher inputs or when the regulator is disabled via the enable pin. See the quiescent current graph under the description tab for more information.

File downloads

Frequently-asked questions

No FAQs available.

On the blog

No blog posts to show.