This is a merged information page for Item #5198.
View normal product page.
Pololu item #:
5198
Brand:
Pololu
Status:
Active and Preferred
This is a miniature brushed DC metal gearmotor with a gearbox cross section of 10×12 mm and a 9 mm long, 3 mm diameter D-shaped gearbox output shaft. Cables sold separately.
motor/brush type | gearbox | encoder | |
---|---|---|---|
HPCB 6V: high-power 6V with carbon brushes | 297.92:1 with brass plates | 12 CPR incremental quadrature with back connector |
voltage | no-load performance | stall extrapolation* |
---|---|---|
6 V | 110 RPM, 150 mA | 3.4 kg⋅cm (47 oz⋅in), 1.5 A |
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
Alternatives available with variations in these parameter(s): gear ratio motor type encoder Select variant…
Compare all products in 6V High-Power Carbon Brush (HPCB) Micro Metal Gearmotors.
![]() |
Micro Metal Gearmotor with 12 CPR encoder, back connector. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, side connector. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, back connector (cable not included). |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, side connector (cable not included). |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, back connector. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, side connector. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, back connector. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, side connector. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, back connector. |
---|
![]() |
Micro Metal Gearmotor with 12 CPR encoder, side connector. |
---|
![]() |
Rear view of Micro Metal Gearmotor with 12 CPR encoder, back connector. |
---|
![]() |
Rear view of Micro Metal Gearmotor with 12 CPR encoder, side connector. |
---|
![]() |
Pin 1 (M1) on the Micro Metal Gearmotors with encoders. |
---|
![]() |
Encoder A and B outputs of a magnetic encoder on a high-power (HP) 6V Micro Metal Gearmotor running at 6 V. |
---|
![]() |
Schematic diagram of the integrated Micro Metal Gearmotor encoder. |
---|
![]() |
Micro Metal Gearmotor next to a US quarter dollar for size reference. |
---|
![]() |
Micro Metal Gearmotor size comparison of 1000:1 (bottom) vs other gear ratios (top). |
---|
![]() |
Micro Metal Gearmotor (standard version without encoder or extended motor shaft). |
---|
![]() |
Micro Metal Gearmotor with extended motor shaft. |
---|
![]() |
Micro Metal Gearmotor HPCB long-life carbon brushes (left) next to Micro Metal Gearmotor HP precious metal brushes (right). |
---|
![]() |
Pololu Wheel 32×7mm on a Micro Metal Gearmotor. |
---|
![]() |
12mm Hex Wheel Adapter for 3mm Shaft on a Micro Metal Gearmotor. |
---|
![]() |
Micro Metal Gearmotor mounted to a piece of acrylic with black mounting bracket version. |
---|
![]() |
Micro Metal Gearmotor mounted to a piece of acrylic with black mounting bracket version. |
---|
![]() |
37D mm Metal Gearmotor next to a Micro Metal Gearmotor for size comparison. |
---|
Our Micro Metal Gearmotor family consists of tiny brushed DC metal gearmotors with nitride-hardened martensitic stainless steel gears in a wide range of gear ratios, motor windings, brushes, and encoder configurations:
![]() |
Micro Metal Gearmotor next to a US quarter dollar for size reference. |
---|
Gear ratio options | Motor winding/brush options | Encoder options |
---|---|---|
|
|
|
The following comparison table shows basic specifications for all of the available versions (see the Micro Metal Gearmotor datasheet (5MB pdf) for additional information, including detailed performance graphs):
Rated Voltage |
Stall Current |
No-Load Current |
No-Load Speed (RPM) |
Extrapolated Stall Torque |
Max Power (W) |
Approx Gear Ratio |
![]() No Encoder |
![]() w/ Extended Motor Shaft |
![]() w/ Encoder, Back Conn. |
![]() w/ Encoder, Side Conn. |
|
---|---|---|---|---|---|---|---|---|---|---|---|
(kg⋅cm) | (oz⋅in) | ||||||||||
HPCB 12V (high-power, carbon brushes) |
|||||||||||
12 V | 0.75 A | 100 mA | 6800 | 0.09 | 1.3 | – | 5:1 | #3036 | #3047 | #5204 | #5205 |
80 mA | 3400 | 0.17 | 2.4 | 1.5 | 10:1 | #3037 | #3048 | #5206 | #5207 | ||
2200 | 0.25 | 3.5 | 1.4 | 15:1 | #4788 | #4789 | #5208 | #5209 | |||
1100 | 0.39 | 5.4 | 1.1 | 30:1 | #3038 | #3049 | #5210 | #5211 | |||
650 | 0.67 | 9.3 | 1.1 | 50:1 | #3039 | #3050 | #5212 | #5213 | |||
450 | 1.0 | 14 | 1.1 | 75:1 | #3040 | #3051 | #5214 | #5215 | |||
330 | 1.3 | 18 | 1.1 | 100:1 | #3041 | #3052 | #5216 | #5217 | |||
220 | 1.8 | 25 | 1.0 | 150:1 | #3042 | #3053 | #5218 | #5219 | |||
160 | 2.5 | 35 | 1.0 | 210:1 | #3043 | #3054 | #5220 | #5221 | |||
130 | 3.0 | 42 | 1.1 | 250:1 | #3044 | #3055 | #5222 | #5223 | |||
110 | 3.3 | 46 | 1.0 | 298:1 | #3045 | #3056 | #5224 | #5225 | |||
85 | 5.0 | 69 | 1.1 | 380:1 | #4798 | #4799 | #5226 | #5227 | |||
35 | 10 | 140 | – | 1000:1 | #3046 | #3057 | #5228 | #5229 | |||
Rated Voltage |
Stall Current |
No-Load Current |
No-Load Speed (RPM) |
Extrapolated Stall Torque |
Max Power (W) |
Approx Gear Ratio |
No Encoder | w/ Extended Motor Shaft |
w/ Encoder, Back Conn. |
w/ Encoder, Side Conn. |
|
(kg⋅cm) | (oz⋅in) | ||||||||||
HPCB 6V (high-power, carbon brushes) |
|||||||||||
6 V | 1.5 A | 170 mA | 6500 | 0.09 | 1.3 | – | 5:1 | #3060 | #3082 | #5178 | #5179 |
150 mA | 3300 | 0.17 | 2.4 | 1.3 | 10:1 | #3061 | #3071 | #5180 | #5181 | ||
2100 | 0.25 | 3.5 | 1.3 | 15:1 | #4786 | #4787 | #5182 | #5183 | |||
1100 | 0.45 | 6.2 | 1.2 | 30:1 | #3062 | #3072 | #5184 | #5185 | |||
650 | 0.74 | 10 | 1.2 | 50:1 | #3063 | #3073 | #5186 | #5187 | |||
430 | 1.1 | 15 | 1.3 | 75:1 | #3064 | #3074 | #5188 | #5189 | |||
330 | 1.6 | 22 | 1.3 | 100:1 | #3065 | #3075 | #5190 | #5191 | |||
220 | 2.0 | 28 | 1.1 | 150:1 | #3066 | #3076 | #5192 | #5193 | |||
160 | 2.8 | 39 | 1.1 | 210:1 | #3067 | #3077 | #5194 | #5195 | |||
130 | 3.2 | 44 | 1.1 | 250:1 | #3068 | #3078 | #5196 | #5197 | |||
110 | 3.4 | 47 | 1.0 | 298:1 | #3069 | #3079 | #5198 | #5199 | |||
85 | 5.0 | 69 | 1.1 | 380:1 | #4796 | #4797 | #5200 | #5201 | |||
33 | 11 | 150 | – | 1000:1 | #3070 | #3080 | #5202 | #5203 | |||
Rated Voltage |
Stall Current |
No-Load Current |
No-Load Speed (RPM) |
Extrapolated Stall Torque |
Max Power (W) |
Approx Gear Ratio |
No Encoder | w/ Extended Motor Shaft |
w/ Encoder, Back Conn. |
w/ Encoder, Side Conn. |
|
(kg⋅cm) | (oz⋅in) | ||||||||||
HP 6V (high-power) |
|||||||||||
6 V | 1.6 A | 120 mA | 6100 | 0.11 | 1.5 | – | 5:1 | #1000 | #2210 | #5152 | #5153 |
100 mA | 3100 | 0.22 | 3.0 | 1.6 | 10:1 | #999 | #2211 | #5154 | #5155 | ||
2000 | 0.30 | 4.2 | 1.5 | 15:1 | #4784 | #4785 | #5156 | #5157 | |||
1000 | 0.57 | 7.9 | 1.5 | 30:1 | #1093 | #2212 | #5158 | #5159 | |||
590 | 0.86 | 12 | 1.3 | 50:1 | #998 | #2213 | #5160 | #5161 | |||
410 | 1.3 | 18 | 1.4 | 75:1 | #2361 | #2215 | #5162 | #5163 | |||
310 | 1.7 | 24 | 1.3 | 100:1 | #1101 | #2214 | #5164 | #5165 | |||
210 | 2.4 | 33 | 1.2 | 150:1 | #997 | #2386 | #5166 | #5167 | |||
150 | 3.0 | 42 | 1.1 | 210:1 | #996 | #2216 | #5168 | #5169 | |||
120 | 3.4 | 47 | 1.1 | 250:1 | #995 | #2217 | #5170 | #5171 | |||
100 | 4.0 | 56 | 1.1 | 298:1 | #994 | #2218 | #5172 | #5173 | |||
84 | 5.5 | 76 | 1.1 | 380:1 | #4794 | #4795 | #5174 | #5175 | |||
31 | 12 | 170 | – | 1000:1 | #1595 | #2373 | #5176 | #5177 | |||
Rated Voltage |
Stall Current |
No-Load Current |
No-Load Speed (RPM) |
Extrapolated Stall Torque |
Max Power (W) |
Approx Gear Ratio |
No Encoder | w/ Extended Motor Shaft |
w/ Encoder, Back Conn. |
w/ Encoder, Side Conn. |
|
(kg⋅cm) | (oz⋅in) | ||||||||||
MP 6V (medium-power) |
|||||||||||
6 V | 0.67 A | 80 mA | 4400 | 0.06 | 0.8 | – | 5:1 | #2362 | #2376 | #5126 | #5127 |
70 mA | 2200 | 0.11 | 1.5 | – | 10:1 | #2363 | #2377 | #5128 | #5129 | ||
1400 | 0.20 | 2.8 | 0.70 | 15:1 | #4782 | #4783 | #5130 | #5131 | |||
720 | 0.33 | 4.6 | 0.57 | 30:1 | #2364 | #2378 | #5132 | #5133 | |||
420 | 0.54 | 7.5 | 0.55 | 50:1 | #2365 | #2379 | #5134 | #5135 | |||
290 | 0.78 | 11 | 0.54 | 75:1 | #2366 | #2380 | #5136 | #5137 | |||
220 | 0.94 | 13 | 0.50 | 100:1 | #2367 | #2381 | #5138 | #5139 | |||
150 | 1.3 | 18 | 0.48 | 150:1 | #2368 | #2382 | #5140 | #5141 | |||
100 | 1.7 | 24 | 0.46 | 210:1 | #2369 | #2383 | #5142 | #5143 | |||
88 | 2.2 | 31 | 0.48 | 250:1 | #2370 | #2384 | #5144 | #5145 | |||
73 | 2.4 | 33 | 0.44 | 298:1 | #2371 | #2385 | #5146 | #5147 | |||
57 | 3.6 | 50 | 0.53 | 380:1 | #4792 | #4793 | #5148 | #5149 | |||
22 | 6.7 | 93 | – | 1000:1 | #2372 | #3059 | #5150 | #5151 | |||
Rated Voltage |
Stall Current |
No-Load Current |
No-Load Speed (RPM) |
Extrapolated Stall Torque |
Max Power (W) |
Approx Gear Ratio |
No Encoder | w/ Extended Motor Shaft |
w/ Encoder, Back Conn. |
w/ Encoder, Side Conn. |
|
(kg⋅cm) | (oz⋅in) | ||||||||||
LP 6V (low-power) |
|||||||||||
6 V | 0.36 A | 50 mA | 2500 | 0.05 | 0.7 | – | 5:1 | #1100 | #2200 | #5100 | #5101 |
40 mA | 1300 | 0.10 | 1.4 | – | 10:1 | #1099 | #2201 | #5102 | #5103 | ||
860 | 0.17 | 2.4 | 0.37 | 15:1 | #4780 | #4781 | #5104 | #5105 | |||
450 | 0.29 | 4.0 | 0.31 | 30:1 | #993 | #2202 | #5106 | #5107 | |||
270 | 0.44 | 6.1 | 0.29 | 50:1 | #1098 | #2203 | #5108 | #5109 | |||
180 | 0.64 | 8.9 | 0.29 | 75:1 | #2360 | #2209 | #5110 | #5111 | |||
130 | 0.74 | 10 | 0.25 | 100:1 | #992 | #2204 | #5112 | #5113 | |||
90 | 1.1 | 15 | 0.25 | 150:1 | #1097 | #2205 | #5114 | #5115 | |||
65 | 1.6 | 22 | 0.25 | 210:1 | #1096 | #2206 | #5116 | #5117 | |||
54 | 1.7 | 24 | 0.23 | 250:1 | #1095 | #2207 | #5118 | #5119 | |||
45 | 2.0 | 28 | 0.22 | 298:1 | #1094 | #2208 | #5120 | #5121 | |||
36 | 2.9 | 40 | 0.27 | 380:1 | #4790 | #4791 | #5122 | #5123 | |||
13 | 5.5 | 76 | – | 1000:1 | #1596 | #3058 | #5124 | #5125 |
Note: Stalling or overloading gearmotors can greatly decrease their lifetimes and even result in immediate damage. The recommended upper limit for instantaneous torque is 2.5 kg⋅cm (35 oz⋅in) for the 380:1 and 1000:1 gearboxes, and 2 kg⋅cm (25 oz⋅in) for all the other gear ratios; we strongly advise keeping applied loads well under this limit. Stalls can also result in rapid (potentially on the order of seconds) thermal damage to the motor windings and brushes, especially for the versions that use high-power (HP and HPCB) motors; a general recommendation for brushed DC motor operation is 25% or less of the stall current.
In general, these kinds of motors can run at voltages above and below their nominal voltages; lower voltages might not be practical, and higher voltages could start negatively affecting the life of the motor.
The 6V and 12V HPCB motors have long-life carbon brushes, and they offer the same performance at their respective nominal voltages, just with the 12 V motor drawing half the current of the 6 V motor. The 6V HP, MP, and LP motors have shorter-life precious metal brushes, which are generally lower-friction than carbon brushes and preferred for lower-current applications. The HPCB versions (shown on the left in the picture below) can be differentiated from versions with precious metal brushes (shown on the right) by their copper-colored terminals. Note that the HPCB terminals are 0.5 mm wider than those on the other Micro Metal Gearmotor versions (2 mm vs. 1.5 mm), and they are about 1 mm closer together (6 mm vs. 7 mm).
![]() |
![]() |
Micro Metal Gearmotor HPCB long-life carbon brushes (left) next to Micro Metal Gearmotor HP precious metal brushes (right). |
---|
In addition to standard versions that are not intended for use with encoders, we have versions of our Micro Metal Gearmotors available with integrated 12 CPR quadrature encoders on the motor shafts (i.e. on the inputs to the gearbox). These are available in two styles—back connector and side connector—and work with our assortment of 6-pin JST SH-style cables and 6-pin JST SH-style connector boards (cables are not included). A plastic snap-on housing covers the encoder disc and electronics.
We also have motor versions available with an extended motor shaft for adding your own encoder. This 1 mm diameter shaft extends 4.5 mm from the rear of the motor and rotates at the same speed as the input to the gearbox. These versions work with our separately available encoders for Micro Metal Gearmotors.
The table below shows the exact gear ratios for our Micro Metal Gearmotors. All gearboxes have the same overall dimensions except for 1000:1, which is 3.5 mm longer than the others. The gearboxes use brass plates on all versions except 380:1, which has steel plates for increased durability and resistance to wear from radial loads.
Please note that the higher gear ratios can generate enough torque to damage themselves if exposed to loads beyond what they are rated for (25 kg⋅mm for 1000:1 and 380:1, 20 kg⋅mm for everything else). The point of these higher gear ratios is not to deliver more overall torque but rather to allow for slower speeds at a given voltage and to draw less current for a given torque within its rated operating range.
Our Micro Metal Gearmotors all have gearboxes with a 10 × 12 mm cross section and a 9 mm-long, 3 mm-diameter D-shaped gearbox output shaft. The gearbox length is the same for all gear ratios except 1000:1, which is 3.5 mm longer than the others. On versions without an encoder, the motor fits entirely within the 10 × 12 mm gearbox cross section. The two encoder options fit within the gearbox cross section on the side opposite the connector and extend past it by 3 mm or 4 mm on the connector side, depending on the connector orientation; for the other two sides, the encoder extends past the gearbox cross section by 0.25 mm.
In terms of size, these gearmotors are very similar to Sanyo’s popular 12 mm NA4S DC gearmotors, and gearmotors with this form factor are sometimes also referred to as N20 motors. The versions with carbon brushes (HPCB) have slightly different terminal and end-cap dimensions than the versions with precious metal brushes, but all of the other dimensions are identical.
See our detailed dimension diagrams (635k pdf) for more information.
![]() |
Micro Metal Gearmotor with 12 CPR encoder, back connector. |
---|
Gearmotor details:
motor/brush type | gearbox | encoder | |
---|---|---|---|
HPCB 6V: high-power 6V with carbon brushes | 297.92:1 with brass plates | 12 CPR incremental quadrature with back connector |
Key specifications:
voltage | no-load performance | stall extrapolation* |
---|---|---|
6 V | 110 RPM, 150 mA | 3.4 kg⋅cm (47 oz⋅in), 1.5 A |
* Note: Stall torque and stall current specifications are theoretical values; stalls could damage the motor or gearbox. |
Exact gear ratio: ``(25×34×37×35×38) / (12×9×10×13×10) ~~ bb(297.92:1)``
This gearmotor includes an integrated two-channel incremental Hall effect encoder that senses the rotation of a magnetic disk on a rear protrusion of the motor shaft. The quadrature encoder provides a resolution of 12 counts per revolution (CPR) of the motor shaft when counting both edges of both channels. To compute the counts per revolution of the gearbox output, multiply 12 by the gearbox reduction factor. For example, for a 50:1 gearbox, the encoder would provide approximately 617 CPR of the gearbox output shaft (see exact gear ratios above).
|
|
The encoder features a 6-pin JST SH-style male connector that works with our 6-pin JST SH-style cables and 6-pin JST SH-style connector boards. Two connector orientations are available: Back Connector, which is oriented parallel to the motor, and Side Connector, which is perpendicular to the motor. Note: A cable is not included with this gearmotor.
![]() |
Pin | Cable color | Function |
---|---|---|
1 | Red | motor power M1 (“+” terminal) |
2 | Black | motor power M2 (other terminal) |
3 | Blue | encoder Vcc (2.7 V to 18 V) |
4 | Yellow | encoder channel A output |
5 | White | encoder channel B output |
6 | Green | encoder GND |
|
|
The motor terminals are connected to the M1 (pin 1) and M2 (pin 2) connector pins, and they can be accessed via the red and black wires when used with our corresponding JST cables. For consistency, M1 always connects to the motor terminal marked with a “+” on the back of the motor case. This mark is not visible on the encoder versions because the board covers it, but it can be seen on the versions without encoders. Please note that this is just an identifying mark, and the motor is intended to be operated in both directions by alternating the polarity of the power to the motor leads. Because the two connector types have pin 1 on opposite sides, they have to be mounted with different motor orientations to ensure pin 1 always connects to the same motor terminal, regardless of encoder style.
|
|
The sensors are powered through the Vcc (pin 3, blue wire) and GND (pin 6, green wire) pins; Vcc can be 2.7 V to 18 V. The quadrature outputs A and B (yellow and white wires) are digital signals that are either driven low (0 V) or pulled to Vcc through 10 kΩ pull-up resistors, depending on the orientation of the motor. The sensors’ comparators have built-in hysteresis, which prevents spurious signals in cases where the motor is near a transition point. The A and B signals are square waves with roughly 50% duty cycles that are approximately 90° out of phase. The order of the A-B transitions indicates motor direction, and the frequency indicates motor speed. The following scope capture shows an example of these signals:
![]() |
Encoder A and B outputs of a magnetic encoder on a high-power (HP) 6V Micro Metal Gearmotor running at 6 V. |
---|
![]() |
![]() |
Pololu Wheel 32×7mm on a Micro Metal Gearmotor. |
---|
![]() |
Black Pololu Wheel 70×8mm on a Pololu Micro Metal Gearmotor. |
---|
![]() |
A pair of Pololu universal aluminum mounting hubs for 3 mm diameter shafts. |
---|
![]() |
12mm Hex Wheel Adapter for 3mm Shaft on a Micro Metal Gearmotor. |
---|
![]() |
Black micro metal gearmotor mounting bracket pair with included screws and nuts. |
---|
![]() |
White micro metal gearmotor mounting bracket pair with included screws and nuts. |
---|
![]() |
Pololu micro metal gearmotor bracket extended with Micro Metal Gearmotor. |
---|
![]() |
MP6550 Single Brushed DC Motor Driver Carrier. |
---|
![]() |
Motoron M1T550/M1U550 Single Motor Controller (Header Pins Soldered). |
---|
![]() |
Motoron M2T550/M2U550 Dual Motor Controller (Header Pins Soldered). |
---|
![]() |
Three Motoron M3S550 shields being controlled by an Arduino Uno. |
---|
![]() |
ACS724LLCTR-2P5AB Current Sensor Carrier -2.5A to +2.5A. |
---|
We also incorporate these motors into some of our products, including our Zumo robot and 3pi robot :
Size: | 10 × 12 × 32 mm1 |
---|---|
Weight: | 11 g |
Shaft diameter: | 3 mm2 |
Gear ratio: | 297.92:1 |
---|---|
No-load speed @ 6V: | 110 rpm3 |
No-load current @ 6V: | 0.15 A4 |
Stall current @ 6V: | 1.5 A5 |
Stall torque @ 6V: | 3.4 kg·cm5 |
Max output power @ 6V: | 1.0 W |
Encoder: | 12 CPR encoder with back connector |
Long-life carbon brushes?: | Y |
Motor type: | 1.5A stall @ 6V (HPCB 6V - carbon brush) |
Max efficiency @ 6V: | 26 % |
---|---|
Speed at max efficiency: | 85 rpm |
Torque at max efficiency: | 0.74 kg·cm |
Current at max efficiency: | 0.42 A |
Output power at max efficiency: | 0.65 W |
This file contains 3D models (in the step file format) of the for the various versions of the Micro Metal Gearmotors.
No FAQs available.
No blog posts to show.